Caple CE1500 Manual de usuario Pagina 146
- Pagina / 244
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
146 Publication 2711P-UM001G-EN-P - September 2007
Chapter 6 Install and Replace Components
PanelView Plus 400 and 600 Terminals
Follow these steps to install a communication module.
1. Disconnect power from the terminal.
2. Set the terminal, display side down, on a clean, flat, stable
surface.
3. Remove the label covering the connectors on the base unit of
the terminal.
4. Position the communication module over back of the terminal
so that the connector on bottom of communication module align
with the connector on the base unit.
REMOVE LABEL TO INSTALL
COMMUNICATION MODULE
Captive
Screws
Tighten this
screw first.
- PanelView Plus Terminals 1
- Important User Information 2
- Summary of Changes 3
- Objectives 5
- Intended Audience 5
- Parts List 5
- Additional Resources 6
- Software and Firmware 6
- Upgrades 6
- Table of Contents 7
- 8 Table of Contents 8
- Table of Contents 9 9
- 10 Table of Contents 10
- Overview 11
- PanelView Plus 400 and 600 12
- Terminals 12
- Base-configured Units 13
- Communication Modules 14
- Power Options 14
- Display and Input Options 15
- PanelView Plus 700 to 1500 17
- Modular Components 18
- Base-configured Unit 18
- Display Modules 20
- Keypad or Keypad and Touch 21
- Catalog Number 22
- Configuration 22
- PanelView Plus Product 22
- Overview Chapter 1 23
- Chapter 1 Overview 24
- Installation 29
- Application Information 31
- Environment and Enclosure 32
- Outdoor Installation for 32
- High-bright Displays 32
- Clearances 34
- Cutout Dimensions 34
- Mount the 400 or 600 35
- Terminal in a Panel 35
- Mount the 700 to 1500 37
- Product Dimensions 39
- PanelView Plus 600 Dimensions 40
- Power Connections 45
- Remove and Install the 46
- Power Terminal Block 46
- 700 to 1500 Terminals 47
- 48 Power Connections 48
- DC Power Connections 49
- Functional Earth Connection 50
- Connect DC Power 51
- AC Power Connections 52
- Connect AC Power 54
- Reset the Terminals 55
- 56 Power Connections 56
- Configuration Mode 57
- Navigation Buttons 59
- Enter or Edit Data 60
- Load an Application 61
- Run an Application 62
- Application Settings 62
- Terminal Settings 62
- Configure Communications 63
- Communication Driver 64
- Ethernet Driver 64
- Has no properties to edit 64
- DHPlus Properties 65
- DH-485 Properties 65
- Remote I/O Properties 65
- ControlNet Properties 65
- DeviceNet Properties 65
- Serial Properties 66
- Configure Network 68
- Information 68
- Define an Ethernet IP Address 69
- Define Name Server Addresses 71
- Configure Diagnostics 72
- Remote Log Destination 73
- Message Routing 73
- Manage Files on the 74
- Terminal 74
- List of files stored 75
- Modify Display Settings 77
- Adjust the Display Contrast 78
- Adjust the Display Intensity 78
- Configure the Screen Saver 79
- Font Linking 81
- Configure Keypad 82
- Keyboard, or Mouse 82
- Configure the Touch Screen 84
- 3. Press OK 85
- Configure Print Options 87
- 4. Press OK when done 88
- Configure Startup Options 89
- Example: 92
- Configure Startup Tests 95
- View and Clear the System 97
- Event Log 97
- Display Terminal 98
- Display FactoryTalk View 100
- ME Station Information 100
- Modify the Date, Time, or 101
- Time Zone 101
- Change the Time 102
- Change the Time Zone 103
- Modify Regional Settings 104
- Change the Time Format 106
- Change the Short Date Format 107
- Change the Long Date Format 108
- Chapter Objectives 109
- Windows CE .NET 109
- Architecture 109
- Programs 110
- Operating System 111
- Keyboard Shortcuts 112
- Start Menu and Taskbar 113
- Command Bar 113
- Find Files 114
- Browse Web Pages 114
- PanelView Plus CE Memory 115
- Dynamic RAM 116
- External CompactFlash Cards 116
- USB Mass Storage Devices 116
- Control Panel Applications 117
- Network ID 118
- Password 119
- ActiveSync Connection 120
- Configure Ethernet Connection 120
- PC Connection 121
- Double-tap Sensitivity 122
- Calibration 122
- Keyboard 123
- Key Repeat 124
- Multi-Key/Hold-Off Lockout 124
- Input Panel 125
- Background 126
- Appearance 126
- Backlight 127
- Screen Saver 127
- Extended Diagnostics 128
- Hardware Monitor 130
- Device Name 132
- Copyrights 132
- Date/Time 133
- Regional Settings 133
- Internet Options 135
- Certificates 135
- Remove Programs 136
- Storage Manager 136
- Required Tools 137
- Precautions 137
- Compatibility of Terminal 138
- Components 138
- Install RAM or Internal 141
- CompactFlash 141
- Install or Replace the Logic 142
- Captive Screw 143
- Install or Replace a 144
- Communication Module 144
- Replace the Display 148
- (6…8 lb-in) 149
- Replace the Battery 150
- ATTENTION 151
- Replace the Bezel 152
- Display Module Bezel 153
- Replace the Backlight 155
- Remove the Product ID 158
- Replace the Keypad Legend 159
- Use an External 161
- CompactFlash Card 161
- Remove a CompactFlash Card 162
- Terminal Connections 163
- Logic Controller Cable 164
- Controllers 165
- Communication Port 167
- Isolation 167
- USB Ports 168
- Serial Connections 169
- Modem Connection 170
- Construct a Null Modem Cable 170
- Computer Connections 171
- Ethernet Connections 172
- Security Considerations 173
- DH-485/DH+/Remote I/O 174
- Belden 3106A Wire Connections 176
- IMPORTANT 176
- Single Cable Connection 176
- Multiple Cable Connection 176
- 1784-CP14 Cable 177
- 1761-CBL-PM002 Cable 177
- DH+ Network Connections 178
- Remote I/O Connections 179
- ControlNet Module 180
- Minimum Requirements 181
- ControlNet Connections 182
- DeviceNet Module 183
- Related Information 184
- DeviceNet Protocol 184
- DeviceNet Connections 185
- Upgrade Firmware 189
- Firmware Upgrade Wizard 191
- Upgrade Firmware with a 192
- Network (Ethernet) 196
- Connection 196
- PanelView Plus 700 199
- Upgrade the Operating 202
- System (OS) 202
- External CompactFlash Card 204
- Troubleshoot the System 205
- Isolate the Problem 206
- Check the System Event Log 207
- Perform Extended Diagnostics 208
- Startup Information 209
- Messages 209
- Startup Sequence 210
- Startup Error Messages 211
- Check Terminal 212
- Ethernet Connnection 217
- Application Does Not Run 218
- Configuration Mode Access 218
- File System Errors 218
- Advanced Diagnostics for 219
- CE Terminals 219
- System Identification Errors 220
- Restart in Safe Mode 221
- Clean the Display Window 222
- Specifications 223
- Mechanical 225
- Agency Certifications 226
- Compatible USB Devices 227
- Appendix 229
- Download Fonts to Terminal 229
- PanelView Plus CE 229
- Accessories CD 229
- FactoryTalk View Machine 230
- Edition Fonts CD 230
- Programmable Key Definitions 233
- 238 Index 238
- Index 239 239
- 240 Index 240
- Index 241 241
- 242 Index 242
- Rockwell Automation 244
© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales