Caple C159/95 Manual de usuario descargar pdf

MULTIPROX READER INSTALLATION

Model # 5385AGS00 (Side Mount)

Model # 5385AGB00 (Back Mount)

The MultiProx Reader subsystem is used in conjuction with

the MultiProx Controller to retrofit existing Schlage/

Westinghouse System Sensors. The following instructions

will explain the installation procedure for the MultiProx

Reader. The instructions include these sections:

Important Installation Guidelines

1. The MultiProx Reader must be located a minimum of 6 inches away from electrical wiring, conduit, metal wall studs or metal pipes

from the back.

2. The MultiProx Reader must be located a minimum of 2 inches (5.08cm), on all sides, away from any metal objects including rebar,

metal mesh, sheet metal, or metal beams.

3. Mounting the MultiProx Reader in an enclosure is acceptable, provided that a minimum of 3 inches (7.62cm) clearance is main-

tained on all sides (no metal on the front).

4. Insulate all cable connectors with electrical tape or shrink tubing so contact is not made with any metal or conductive material.

5. The MultiProx Reader should not be mounted within 6 feet of any monitors (VDTs or CRTs). The scan frequencies of most monitors

may interfere with the signal received from the access control cards. Motors and electronic devices generate RF noise that may

interfere with the reception of the signal from an access control card.

Parts List (Included) Quantity

1) MultiProx Reader (p/n 5385AGS or B) 1

2) Installation Manual 1

3) Label for front cover- HID logo 1

4) Terminal Connector 1

Not Included

Parts Recommended

1) Cable, Coax - RG6 or SE 9284 A/R

1000ft Maximum

2) Electrical tape or shrink tubing A/R

Parts Recommended (If this is not a Retrofit)

1) F-56 crimp-on connectors 2

2) Crimping tool 1

INSTALLATION REQUIREMENTS

MultiProx System Layout Diagram

Important Installation Guidelines

MultiProx Reader Installation

Mounting Instructions: Retrofitting an existing Sensor

Connecting the Reader Cable to the MultiProx Controller

Configuring the DIP Switch Settings on the MultiProx Controller

Specifications for the MultiProx Reader

MULTIPROX CONTROLLER

ACCESS

CONTROL

PANEL

ACCESS

CONTROL

SYSTEM HOST

HSM

ULTIPROX READERS

WIEGAND & RELAY OUTPUTS

READER 1 WIEGAND DATA

READER 8 WIEGAND DATA

HSM 1 RELAY OUTPUTS

HSM 8 RELAY OUTPUTS

TBW1

TBW8

TBR1

TBR8

AXIMUM - 8 READER CHANNELS

READER CHANNEL 1

EADER CHANNEL 8

MultiProx System Layout Diagram

KEY

EXISTING RG/6 COAX

ALPHA 1295 OR EQUIVALENT PER CHANNEL

ALPHA 1292 OR EQUIVALENT PER OUTPUT

UP TO - 8 RELAYS &

8 W

IEGAND CONNECTORS

1 2

Indice de contenidos

Pagina 1 - INSTALLATION REQUIREMENTS

MULTIPROX READER INSTALLATIONModel # 5385AGS00 (Side Mount)Model # 5385AGB00 (Back Mount)The MultiProx Reader subsystem is used in conjuction witht

Pagina 2 - PROX CONTROLLER

MultiProx Reader Installation Mounting Instructions:Retrofitting an existing Sensor1. Locate the existing Schlage/Westinghouse Sensor.Determine th

Mas documentos para No Caple C159/95

a Ver el documento Caple C159/95 Manual de usuario

Caple C159/95 Manual de usuario (11 paginas)

Caple C159/95 Manual de usuario (6 paginas)

Comentarios a estos manuales

Sin comentarios

Caple C159/95 Manual de usuario

Busca en linea o descarga Manual de usuario para No Caple C159/95. MultiProx (Reader #5385) Manual de usuario

Indice de contenidos

Mas documentos para No Caple C159/95

Comentarios a estos manuales

Relacionado con productos y manuales para No Caple C159/95